HGT Precision Sequential 5 Speed
HGT Sequential 5 Speed 7075 T6 Billet CNC'd Case
HGT Authorized Dealer
**Online checkout not valid, Pricing will be emailed to you**
You will need following parts to complete installation:
(click on below to add to cart)
- Bell house
- Gear display
- Clutch Release bearing and shims
HGT Sequential 5 Speed
7075-T6 Billet CNC'd Case
Straight Cut and Diamond Ground to DIN5/6 standard for maximum efficiency and even load transfer across the gear teeth. Constant mesh dog engagement for shifts as quick as 30 milli-seconds. Probably the worlds quietest straight cut geared dog box, with almost none of the whine traditionally assoicated with this industry race standard. You’ll be amazed how quiet this gearbox is (as in totally streetable) and just how cool it runs.
Outlet and Inlet for lines to oil pump, oil filter and oil cooler options
Oil Temperature sensor
Oil Drain with magnetic plug
1000 nm / 738 ftlb / 102kg and 11,000 RPM
38.5kg or 85lb
1st 2.44 2.16 2.60
2nd 1.80 1.80 2.16
3rd 1.42 1.42 1.80
4th 1:18 1.18 1.28
5th 1:1 1:1 1:1
Rev 2.94 on all
OEM INPUT SHAFTS FOR
GM 26 tooth spline
GM/Nissan 26 tooth spline with Nissan spigot
Mazda 23 tooth spline
Nissan 24 tooth spline
Toyota 21 tooth spline (R154)
Toyota 14 tooth spline (V160 / V161/ 6MT)
Others possible on request
Flange pre drilled for 1350 series Yoke or 1350 series Slip Yoke – supplied with hardware. Comes pre-fitted with a reluctor wheel ready to accept our Speed Sensor to eanble launch control, traction control, speed referenced boost or a digital speedometer.
HGT Billet CNC gear lever systems with remote mount base for Centre Tunnel or Right Offset mounting positions. 3 different height options to accomodate driver preference. Reverse can either be integrated on the shift lever or remotely mounted.
HGT Shift Cut Knob
HGT Billet Brackets for Motec & Geartronics Paddleshift actuators
HGT Billet CNC Digital Gear Postion Display
HGT Billet Clutch Release Bearing with Shims
HGT Billet Speed Sensor Bracket and GT101 Sensor
HGT Breather Kit
1350 Series Yoke or Slip Yoke - bolts up to output flange and welds to driveshaft
Cast or Billet CNC Custom Bell Houses to allow direct bolt up of HGT Gearboxes to:
BMW: Straight 6 M50, V8 M60, M62, S62, S65, V10 S85
GM LS/SBC: OEM setup with168 tooth ring gear, front mount starter motor, 11”/12” clutch AND Race setup with cover mounted 110 tooth ring gear, rear mount starter motor and 5.5"/7.25" clutch
Ford: Windsor, Coyote
Honda - K20/K24 in rear wheel drive configuration
Mazda: Series 6 Rotary with rear starter motor mount
Mitsubishi: EVO 1/2/3 in rear wheel drive configuration
Nissan: SR20, RB20, RB25, RB26, RB30, VQ35, VR38
Toyota: 1JZ, 2JZ, 1UZ, 3UZ, 3SGTE
Other Bell Houses available on request...just ask.
Our Gearboxes come standard with the GM Muncie pattern on the front mount, with bell houses to suit most popular race engines.
Whilst some say that “any old bell-house will work” or “I will buy one from my local guy – he’s cheap and cheerful”; this is one of the most critical parts in the whole drivetrain setup. The front and rear facing plates must be 100% parallel, centres must be perfectly aligned, bolt-holes must be drilled in exactly the right position and at exactly the right angle. Many so called “gearbox problems” are actually the result of a poorly built, machined or drilled bell housings. Misalignment of just 10 microns can be sufficient to cause premature bearing failure or abnormal shaft or internal wear. It’s simply not worth trying to “save a little” when there’s a sizable gearbox investment at stake. All HGT Precision bell housings are built to handle race loadings, are aligned perfectly and have the drillings in exactly the right place to make installation simple. As is standard practise in the race industry, you should index the bell to your crank and block to ensure everything is perfectly aligned.
We have current setups for:
- BMW Inline 6, V8, V10
- Ford Coyote, Windsor
- GM LS, SBC
- Honda K24 in RWD setup
- Mazda Rotary Series 6
- Mitsubishi Evo 1,2,3,4 in RWD setup
- Nissan SR20, RB25, RB26, RB30, VQ35, VR38
- Toyota 1JZ, 2JZ, 1UZ, 3UZ, 3SGE
- We also offer most of these Bells in CNC Billet form. Clearly they cost substantially more, but for those wanting the best - then this is the gold standard.
As we're continually developing new setups, if yours isn’t listed just ask, we can probably accomodate you.
All gearboxes are custom built to order with our flexible supply chain and assembly process meaning we can generally ship within 3 weeks of receiving your order and deposit.
We ship our Sequential Race Gearboxes and Transmissions by airfreight as its fast (4-6 days) and trackable. For most countries, the is no charge for airfreight to your nearest International airport. All product is shipped with insurance cover to the destination airport. For an additional fee (at cost) we can arrange door-to-door delivery.
SHIPPING VIA - FEDEX, DHL or EMS for security, tracking and fast delivery. Shipping price will be added to your final invoice or sent on a separate invoice depending how the customer purchases the item(s). Item(s) will ship once all payment(s) have been made in full.